txdot wet ball mill

Mar 07, 2006· Mar 07, 2006· Wet Ball Value or L.A. Abrasion Testing Alternatives. Wet Ball Value or L.A. Abrasion Testing Alternatives. SETlabguy (Geotechnical) (OP) 7 Mar 06 18:00. We have a client requesting a wet ball value (TXDOT TEST METHODS 116-E) or, as an alternative, an LA Abrasion Test. The problem is they don't have enough material to run either test.

Resistance to Degradation by Wet Ball Mill Method: Tx117: Triaxial Compression Tests: Tex-117-E: Tx120: Soil-Cement Testing: Tx120-21: Soil-Cement or Lime Testing: Tx121: Soil-Lime Testing: Tx121P3: Determining Stabilization Ability of Lime by Soil pH: Tx123: Determining the Drainage Factor of Soil Materials: Tx124: Potential Vertical Rise ...

TxDOT Specifications. Apr 16, 2004 7) Wet ball mill will be required instead of soundness, unless otherwise shown on the plans. 8) Recycled asphalt pavement (RAP) and other recycled materials may be used when shown on the plans. 9) When RAP is allowed, do not exceed 20%. Get Price.

tin) and 6 other TxDOT district labs par-ticipated in the above round-robin test program. Accordingly, each of the se-lected 12 sources was tested in 4 labs. Each lab performed 5 repetitions of MSS and MD tests on each of the sources assigned to it. Phase II investigation con-sisted of a comparative study of the Texas Wet Ball Mill test and the ...

BALL MILL METHOD FOR DETERMINING THE DISINTEGRATION OF FLEXIBLE BASE MATERIAL TXDOT DESIGNATION: TEX-116-E CONSTRUCTION DIVISION 3 – 5 LAST REVIEWED: SEPTEMBER 2014 water for one hour. If 2 L (0.5 gal.) of water do not fully cover the sample, use the smallest amount of water possible to do so. Note 1—Use the dry sieve analysis as a rough check for specification …

Apr 16, 2004· 7) Wet ball mill will be required instead of soundness, unless otherwise shown on the plans. 8) Recycled asphalt pavement (RAP) and other recycled materials may be used when shown on the plans. 9) When RAP is allowed, do not exceed 20% …

Resistance to Degradation by Wet Ball Mill Method: Tx117: Triaxial Compression Tests: Tex-117-E: Tx120: Soil-Cement Testing: Tx120-21: Soil-Cement or Lime Testing: Tx121: Soil-Lime Testing: Tx121P3: Determining Stabilization Ability of Lime by Soil pH: Tx123: Determining the Drainage Factor of Soil Materials: Tx124: Potential Vertical Rise ...

The result of this test is known as the Wet Ball Mill (WBM) value. Apparatus The following apparatus is required: ♦ wet ball mill machine, consisting of a watertight steel cylinder, closed at one end, with inside dimensions of 258.8 ± 3 mm (10.188 ± 1/8 in.) in diameter and 273.1 ± 3 mm (10.75 ± 1/8 in.) in length.

Anchor: #i1013593 Section 3: Flexible Base Selection Anchor: #i1013598 3.1 Introduction. The base course in a pavement structure serves multiple functions, but the primary function is to supply foundational support and capacity to the pavement structure; to provide a stable course to minimize flexural tensile stresses in surface layers; and to dissipate stresses induced by traffic loading to ...

Current Lead Time - 14-21 Days. The Rainhart Aggregate Wet Ball Mill is used to determine the resistance of aggregate in flexible base materials to disintegration in the presence of water. These results are essential in determining whether the base will resist crushing, degradation, disintegration, and premature structural failure.

Wet ball mill, % max.2 40 45 – Wet ball mill, % max. increase passing the No. 40 sieve Tex-116-E 20 20 – As shown on the plans Classification3 1.0 1.1–2.3 – As shown on the plans Min. compressive strength3, psi lateral pressure 0 psi 45 35 – lateral pressure 15 psi …

May 03, 2002· May 03, 2002· 3) When lightweight aggregates are used, the wet ball mill requirements will not apply and the lightweight aggregate shall meet the Los Angeles Abrasion, Pressure Slaking and Freeze Thaw requirements of Item 303, "Aggregate for Surface Treatment (Lightweight)".

TxDOT Desienation of Test Tex-103-E Moisture Content Tex-104-E Liquid Limit Tex-106-E Plasticity Index Tex-107-E, Part II Bar Linear Shrinka~e Tex-110-E Sieve Analysis Tex-113-E Moisture-Density Determination Tex-116-E Wet Ball Mill Tex-117-E Triaxial Tests Electrical Related to material's propensity to attract and hold moisture

Wet Ball Mill Sample, 6 steel spheres 2" diameter, & water into bucket and rotated 600 revolutions at 60 rpm. Potential degradation during hauling, spreading, and construction. Sieve Analysis (Gradation) Separation of aggregate particles into different sizes from 1-3/4" to material passing #40 sieve (0.02").