infrared asphalt repair process

Infrared Patching is the process of combining hot-mix asphalt with the existing damaged asphalt to compact the area for a smooth, seamless finish. In cold weather climates, cracks, divots, potholes, heaving, uneven or rough asphalt surfaces are often a result …

Infrared asphalt repair is the process of heating an asphalt surface until it can be raked, luted and compacted. How Does It Work? When heat is generated, infrared light rays are created. These light rays are directed onto the asphalt surface where they are absorbed into the material. This causes the material to heat up and become workable again.

The infrared process is simply radiation that transfers heat into the damaged asphalt and aids in the repair process. Our repair unit recycles the asphalt in place and reclaims the old asphalt on the damaged surface. When the surface heats up to 300 degrees, it can be reworked to allow new or asphalt. The prepping process is extremely ...

Infrared asphalt repair is the process of heating existing asphalt, then adding new hot-mix asphalt, and then leveling and compacting to create a seamless patch. This technologically advanced process and equipment uses infrared wavelengths to heat asphalt pavement without a direct flame.

Feb 24, 2021· Infrared asphalt repair is quickly becoming the go to repair method for asphalt pavement. Check out this step by step training video from the infrared expert...

Clean Sweep's exclusive asphalt restoration process uses industry-leading infrared repair technology. Clean Sweep's Infrared Restoration Team truly creates the ultimate in asphalt repair. Our infrared restoration process can quickly repair virtually any problem with asphalt as long as the damage has not been caused by a faulty subbase. YouTube.

Minneapolis Infrared Asphalt Repair Process. 1. Heat asphalt until soft After removing any water or debris from the area with powerful blowers, the infrared panel is lowered to a position just above the pavement. The heated area (6×8) is larger than the area to be repaired (5×7).

May 07, 2018· Infrared asphalt repair is a process that involves using infrared technology to heat up asphalt until it softens to a point that the new asphalt can seamlessly blend with the old. It's a good method to choose if you've begun to notice uneven surfaces and other issues on your asphalt.

The process keeps manpower to a minimum, therefore keeping the cost of the repair to a minimum. The time it takes to repair a pothole or failure with infrared is about 1/4 of the time it takes for a total removal and repair of asphalt, allowing interruption of the area to be kept at a minimum.

The Infrared Repair Process is done first by heating the repair area with a large propane heated plate that allows our experienced personnel to remove the surface layer of the cracked asphalt or area around the pothole. They proceed to use hot asphalt from the four ton hopper on the truck or infrared repair trailer and place it in the repair area.

Infrared Road Repair (IRR) is becoming a big business in many city, state and local markets. The overall process is very simple on the surface, yet complex when you get into the details. To properly repair asphalt pavement using this technology you must be aware of a few important factors that will aid in a successful repair and having a happy ...

Infrared asphalt technology is an effective solution for critical repairs. This unique method blends hot-mix asphalt right in with the original and then compacts the area to create a seamless restoration. The Repair Process: The area to be repaired will be swept or blown clean, removing all loose aggregate, sand, and/or water.

Asphalt repairs in 30 Minutes or less! Even severely aged asphalt will soften when heated (about 290 deg. F, 140 deg. C) to the flow point of the asphalt cement. INFRARED heaters are able to evenly raise the temperature of the asphalt repair area without burning …

North American Infrared is a family owned asphalt repair company that offers the only seamless asphalt repair available today. North American Infrared is owned by father and son, and together they have developed and revolutionized the asphalt repair industry with the infrared process.

Seamless infrared repairs, not patches! At Asphalt Restoration, Inc., we use the infrared process for all of our repairs.With the infrared process we can achieve a thermally bonded asphalt repair that blends beautifully with the existing pavement.. With conventional sawcut and remove patching, cracks usually form where the hot asphalt was placed against the cold edge of the surrounding asphalt.

Infrared Repair. Infrared repair is a method of blending new asphalt with infrared-heated existing asphalt to create a seamless repair. The infrared equipment is capable of heating existing asphalt to a depth of approximately 3". There is no direct flame in contact …

Process. 1. Thoroughly sweep the area you will be working on. Remember, Ray-Tech equipment produces true infrared rays (not just heat) and these rays will not penetrate the asphalt if any dirt, sand or puddle/running water is in the way. 2. To light the unit, raise chamber to 45º angle.

Simply put infrared asphalt repair is the process of re heating an asphalt repair area back to its original application temperature of 350 degrees Fahrenheit. Hotbox Reclaimers; KM 1000. KM 1000 The KM 1000 holds a capacity of 1,000 lbs. of material and easily fits into the back of a pickup truck or utility vehicle. The KM 1000 is portable and ...

SPECIALIZED INFRARED ASPHALT RESTORATION. Our repair method is unique to the asphalt repair industry. We utilize a special heating process that makes the asphalt workable again and leaves a seamless thermally bonded repair. The best part is that it's green, meaning we recycle the existing asphalt so we're only using about 5% of new asphalt and ...

With a 3'6" x 6'6" heating area the KM 2-18X infrared asphalt recycler is one of the most versatile infrared units on the market. Equipped two independently ...

For more info, or to view a step-by-step video of how the asphalt infrared repair process works, visit Kasi Infrared; email [email protected]; or call 800-450-8602. Print version: infrared equipment: P.O. Box 895 Claremont, NH 03743 Phone: 603-865-1893 Toll Free: 1-800-450-8602 Fax: 603-865-1896

Infrared Asphalt Repair Technology Saves State And Local Governments. Call Us Today! 800-450-8602 or 603-865-1893. Kasi Equipment, Parts, and Support! PACCAR Financial Special.

Infrared Asphalt Repairs. This type of patching is an alternative to traditional patching methods. The process involves heating up a pavement area to make it workable, then the top lift of existing asphalt is removed. New asphalt is then added to existing asphalt, along with a …

Aug 25, 2021· "Here's a step-by-step guide to the repair process: The area to be treated is swept free from debris and thoroughly dried out, ensuring that nothing blocks the infrared repair process from reaching the asphalt surface. An infrared heater is placed above the damaged asphalt area and is heated for about 5-10 minutes.

The infrared asphalt repair process begins with sweeping or blowing-clean the portion of asphalt in need of repair. The infrared rays cannot effectively permeate dirt, water, and other loose particulates. Once the surface is free of debris, the surface is heated up to 325 degrees Fahrenheit for a duration of five to ten minutes, depending upon ...

With the infrared process, the repair is thermally bonded with the existing asphalt, eliminating cold joints that can be a potential point of weakness. Step by step process: The infrared unit is positioned over the area to be repaired. Approximately 15 minutes later, the pavement becomes hot mix again. Time varies by ambient temperature. This ...

INFRARED ASPHALT REPAIR & REMOVALS. Pavements fail for many reasons. Whether it's a lack of gravel base, insufficient thickness, poor drainage or a combination of these. Asphalt Maintenance and Paving can use infrared technology or our removal process to remedy damaged areas. The result is a smooth, permanent repair.

The Infrared Asphalt Repair Process. Set the infrared machine over the asphalt area to be repaired and have it heat the asphalt for 7-10 minutes. Stepping in 3-6" from the outline of the heated area, rake the existing asphalt by breaking it up so it looks like it did originally.

The Process - Conventional vs. Infrared - Old vs. New. Repairing asphalt by conventional methods is a very expensive and time-consuming process. It requires a significant amount of equipment, material and manpower, and the results are often far from permanent. Even when done correctly, the finished repair is left with a cold seam where hot ...

Title of Document: OPTIMIZATION OF THE INFRARED ASPHALT REPAIR PROCESS Christopher William Leininger, Master of Science, 2015 Directed By: Chair and Professor, Dr. Charles W. Schwartz, Department of Civil and Environmental Engineering Infrared asphalt repair is an alternative technology that potentially allows for