effect of ball size in ball mill

2.4 Effect of ball size 29 2.4.1 Empirical approaches 29 2.4.2 Probabilistic approaches 33 2.5 Abnormal breakage 36 2.6 Effect of ball mixture 37 2.6.1 Ball size distribution in tumbling mills 37 2.6.2 Milling performance of a ball size distribution 40 2.7 Summary 41 Chapter 3 …

40%. The effect of ball size distribution increased with increasing mill filling and for the mill filling of 35%, the ball size distribution had the maximum effect on the power draw. When the mill charge contained mono-sized balls, the ball flow regime inside the mill transited to the cataracting and impact breakage was the main breakage mechanism.

The effect of ball size diameter or ball size distribution on the mill performance have been studied by many researchers using empirical methods, and population balance models (Austin et al., 1976 ...

The variation of ball size in a planetary ball mill (PBM) was studied in terms of its effect on the specific impact energy of balls as a result of ball to ball and ball to vial collision ...

In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter ...

Effect of particle filling and particle size on the net power There is a notable difference in the variation of net power when the powder filling fraction is about 0.6 and 0.5 for rod and with increasing particle filling for both coarse and fine particles ball mills respectively [12].

size distributions and mill scale—up, they have not addressed the primary role of grinding, i.e. liberation. I The present investigation analyzes the effect of ball U mill operating· parameters on the breakage rates of both t· liberated and composite material. The operating parameters studied include mill rotational speed, ball size, mill I

In this study, we investigate the effect of the ball size in a high-energy ball mill on the comminution rate and particle size reduction. High-energy ball milling at 2000 rpm produces ultrafine talc particles with a surface area of 419.1 m 2 /g and an estimated spherical diameter of 5.1 nm.

The specific rates of breakage of particles in a tumbling ball mill are described by the equation S i = ax α i (Q(z), where Q(z) is the probability function which ranges from 1 to 0 as particle size increases.This equation produces a maximum in S, and the particle size of the maximum is related to ball diameter by x m = k 1 d 2.The variation of a with ball diameter was found to be of the form ...

Jul 03, 2017· Jul 03, 2017· If it is desired to find the effect of balls grinding 20-mesh ore and the mill is loaded with 20-mesh material, the grinding time should be infinitely short, because fine particles are made as soon as the mill starts and if the run continues the test is of the comminuted products of the 20-mesh sample rather than that which was supplied for the ...

2.4 Effect of ball size 29 2.4.1 Empirical approaches 29 2.4.2 Probabilistic approaches 33 2.5 Abnormal breakage 36 2.6 Effect of ball mixture 37 2.6.1 Ball size distribution in tumbling mills 37 2.6.2 Milling performance of a ball size distribution 40 2.7 Summary 41 Chapter 3 …

Ball mills are usually the largest consumers of energy within a ... the influence of the shell lifting effect on the grind for a primary grinding duty. Figure 5 shows the evolution of the mill discharge product size in relation to the lifting effect of the liners. In this specific case, it is obvious that a certain load

Jul 03, 2017· If it is desired to find the effect of balls grinding 20-mesh ore and the mill is loaded with 20-mesh material, the grinding time should be infinitely short, because fine particles are made as soon as the mill starts and if the run continues the test is of the comminuted products of the 20-mesh sample rather than that which was supplied for the ...

Dec 01, 2013· The effect of ball size on the particle size reduction has been investigated first for varying rotation speed of the container. Percent passing and size distributions of the milled Al 2 O 3 powder are shown in Fig. 1, Fig. 2, respectively, as a function of particle size for varying ball size.The average particle sizes (d 50) of the milled Al 2 O 3 powder are shown in Fig. 3 as a function of ...

An investigation was conducted to determine the effect of the ball diameter sizes on milling operation. A laboratory size ball mill was used with ball media of sizes 10 mm, 20 mm and 30 mm respectively. Quartz was the material used to perform the experiment and was arranged into 3 mono-sizes namely -8 mm +5.6 mm, -4 mm +2.8 mm and-2 mm +1.4 mm ...

May 30, 2017· Effect of Ball Diameter, or Rod Diameter Variation. The first relationship to be considered is the effect of the variation of the ball diameter, or rod diameter, upon the size distribution obtained. In Fig. 6.1 are shown typical size frequency curves obtained by ball milling; these curves being deduced from the data of Coghill and Devaney.